Understadning Cisco Access-Lists on Switches: PACL, VACL, RACL and MACL - NETSEC

Latest

Learning, Sharing, Creating

Cybersecurity Memo

Thursday, December 31, 2015

Understadning Cisco Access-Lists on Switches: PACL, VACL, RACL and MACL

This 'ACLs on Switches' diagram shows PACL, VACL and RACL location and traffic direction on switch. It is clear and easy understanding.

The following explanation is from Security Features on Switches by .



Access Lists on Switches

The switch supports the following four types of ACLs for traffic filtering:
  • Router ACL
  • Port ACL
  • VLAN ACL
  • MAC ACL

Router ACL

As the name implies, Router ACLs are similar to the IOS ACL discussed in Chapter 2, "Access Control," and can be used to filter network traffic on the switched virtual interfaces (SVI). (SVI interfaces are Layer 3 interfaces on VLANs, on Layer 3 physical interfaces, and on Layer 3 EtherChannel interfaces.) Both standard and extended ACLs are supported. For more details to configure Router ACL, refer to Chapter 2.

Port ACL

Port ACLs are similar to Router ACLs but are supported on physical interfaces and configured on Layer 2 interfaces on a switch. Port ACL supports only inbound traffic filtering. Port ACL can be configured as three type access lists: standard, extended, and MAC-extended.
Processing of the Port ACL is similar to that of the Router ACLs; the switch examines ACLs associated with features configured on a given interface and permits or denies packet forwarding based on packet-matching criteria in the ACL.
When applied to a trunk port, the ACL filters traffic on all VLANs present on the trunk port. When applied to a port with voice VLAN, the ACL filters traffic on both data and voice VLANs.
The main benefit with Port ACL is that it can filter IP traffic (using IP access lists) and non-IP traffic (using MAC access list). Both types of filtering can be achieved—that is, a Layer 2 interface can have both an IP access list and a MAC access list applied to it at the same time.

VLAN ACL (VACL)

VLAN ACL (also called VLAN map) provides packet filtering for all types of traffic that are bridged within a VLAN or routed into or out of the VLAN. Unlike Router ACL, VACL is not defined by a direction (input or output). All packets entering the VLAN (bridged or routed) are checked against the VACL. It is possible to filter traffic based on the direction of the traffic by combining VACLs and Private VLAN features.
VACLs are processed in hardware, so there is no performance penalty in processing them. Therefore, they are also referred to as wire-speed ACLs. The forwarding rate remains unchanged regardless of the size of the access list because the lookup of VACLs is performed in hardware.

VACL on a Bridged Port

Figure 4-2 illustrates where the VACL is processed when VACL is applied on a bridged port for traffic from Host A in VLAN 5 that is communicating to Host B in VLAN 10 through the switch.

Figure 4-2 VACL on a Bridged Port

VACL on a Routed Port

Figure 4-3 illustrates how IOS ACL and VACL are applied on routed packets and Layer 3 switched packets. Following is the order of processing:
  1. VACL for input VLAN
  2. Input IOS ACL
  3. Output IOS ACL
  4. VACL for output VLAN

Figure 4-3 VACL on a Routed Port

Configuring VACL

Perform the following steps to configure and apply a VACL (VLAN access map) on the switch:
  1. Define the standard or extended access list to be used in VACL.
  2. Define a VLAN access map.
  3. Configure a match clause in a VLAN access map sequence.
  4. Configure an action clause in a VLAN access map sequence.
  5. Apply the VLAN access map to the specified VLANs.
  6. Display VLAN access map information.
Example 4-6 shows how to define and apply a VACL to drop packets matching access list 1 from network 192.168.1.0/24; all other packets matching access list 2 are forwarded. The VACL is applied to VLANs 5 through 10.

Example 4-6. VACL Configuration Example

Switch(config)#access-list 1 permit 192.168.1.0 0.0.0.255
Switch(config)#access-list 2 permit any
Switch(config)#vlan access-map mymap 10
Switch(config-access-map)#match ip address 1
Switch(config-access-map)#action drop
Switch(config-access-map)#exit
Switch(config)#vlan access-map mymap 20
Switch(config-access-map)#match ip address 2
Switch(config-access-map)#action forward
Switch(config-access-map)#exit
Switch(config)# vlan filter mymap vlan-list 5-10
Switch(config-access-map)#end

Switch# show vlan access-map
Vlan access-map "mymap"  10                              
  Match clauses:                                         
    ip address: 1                                        
  Action:                                                
    drop                                                 
Vlan access-map "mymap"  20                              
  Match clauses:                                         
    ip address: 2                                        
  Action:                                                
    Forward                                              

Switch# show vlan filter
VLAN Map mymap is filtering VLANs:                       
  5-10                                                   

MAC ACL

MAC ACL, also known as Ethernet ACL, can filter non-IP traffic on a VLAN and on a physical Layer 2 interface by using MAC addresses in a named MAC extended ACL. The steps to configure a MAC ACL are similar to those of extended named ACLs. MAC ACL supports only inbound traffic filtering.
To define the MAC Extended ACL, use the mac access-list extended command. Several non-IP protocols are supported.
After the MAC ACL is created, it can be applied to a Layer 2 interface using the mac access-group [acl-name] in command to filter non-IP traffic received on the interface.
Example 4-7 shows how to define and apply a MAC ACL to drop all (non-IP) AppleTalk Address Resolution Protocol (AARP) packets, allowing all other types of traffic.

Example 4-7. MAC ACL Configuration Example

Switch(config)# mac access-list extended my-mac-acl
Switch(config-ext-macl)# deny any any aarp
Switch(config-ext-macl)# permit any any
Switch(config-ext-macl)# exit
Switch(config)# interface Fastethernet0/10
Switch(config-if)# mac access-group my-mac-acl in
Switch(config-if)# end

No comments:

Post a Comment